Physical Stats
Form Factor µATX
Dimensions 9.6" x 9.6 ", (24.4cm x 24.4 cm)
Processor/Cache
CPU
Single LGA775 ZIF Socket
Supports a Quad-Core Intel® Xeon® 3200 series processor
Supports a Dual-Core Intel® Xeon® 3000 series processor
Supports a Quad-Core Intel® Core™2 Extreme series processor
Supports an Intel® Core™2 Quad series processor
Supports an Intel® Core™2 Duo series processor
Supports an Intel® Pentium® processor E2000 series
Supports a Dual-Core Intel® Pentium® D processor
Supports an Intel® Pentium® Extreme Edition processor
Supports an Intel® Pentium® 4 processor
Supports an Intel® Celeron® processor E1000 series
Supports an Intel® Celeron® processor 400 series
NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45nm processor
System Bus
1066 / 800 / 533 MHz system bus
System Memory
Memory Capacity
Four 240-pin DIMM sockets
Supports up to 8 GB of unbuffered ECC / non-ECC DDR2 667/533MHz memory (Dual Channel)
Memory Type
DDR2 667/533MHz unbuffered ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs
DIMM Sizes
256 MB, 512 MB, 1 GB, 2GB
Memory Voltage
1.8V only
On-Board Devices
Chipset
Intel 3000 (Mukilteo-2) chipset
ICH7R + Intel® 82573V + Intel® 82573L
Serial ATA
Intel® ICH7R SATA2 (3 Gbps) controller built-in
Intel:
RAID 0, 1, 5, 10 support (Windows Only)
IPMI
1U support for Intelligent Platform Management Interface v.2.0 (Optional: AOC-1UIPMI-B )
Network Controllers
1x Intel® 82573V Gigabit PCI-Express Ethernet
1x Intel® 82573L Gigabit PCI-Express Ethernet
Supports 10Base-T, 100Base-TX, 1000BASE-TX, RJ45 output
VGA
On-board XGI Volari Z7 graphics
Super I/O
Winbond 83627HG chip
Clock Generator
CK410
Input / Output
Serial ATA
Four Serial ATA ports (3 Gbps performance)
Four SATA hard drives supported
IDE
One EIDE channel supports up to two UDMA IDE devices
Floppy
1 Floppy controller; 1.44 MB
LAN
2 x RJ45 LAN port
USB
6x USB 2.0 compliant / 1.1 compatible
4x internal USB headers
2x rear ports
VGA
1x VGA Port
Keyboard / Mouse
PS/2 keyboard and mouse ports
Serial Ports
1x Fast UART 16550 serial port
1x Header
|
Chassis ( Optimized for PDSML-LN2+ )
1U Chassis |
2U Chassis |
Mid-Tower |
Tower / 4U Rackmount |
CSE-512F-260
CSE-513F-260
CSE-811i-300
CSE-811T-300 |
CSE-822T-550LP
CSE-823i-550LP
CSE-823T-550LP
CSE-823T-R500LP
CSE-823TQ-R500LP |
CSE-733i-450
CSE-733i-645
CSE-733T-450
CSE-733T-645
CSE-733TQ-645 |
CSE-742i-300
CSE-742i-420
CSE-742i-450
CSE-742i-600
CSE-742T-650
CSE-743i-645 |
Important Note
To ensure system stability, a 300W (minimum) ATX power supply
[4-pin +12V AND (20 or 24-pin)] is recommended.
Expansion Slots
Universal Slot
1 (x8) PCI-Express Slot OR 1x 32-bit 33MHz PCI Slot
PCI-Express
1 (x4) PCI-e (using x8) slot
PCI
1x 32-bit 33MHz PCI (5V) slot
System BIOS
BIOS Type
8Mb Flash EEPROM with Phoenix BIOS®
BIOS Features
Plug and Play (PnP)
DMI 2.3 support
PCI 2.2
ACPI 1.0
ACPI 1.0 (limited)
USB Keyboard support
SMBIOS 2.3
Management
Software
Optional IPMI (Intelligent Platform Management Interface) 2.0
SuperDoctor® III
Watch Dog
NMI
W83793 H/W Monitor
Power Configurations
ACPI/APM Power Management
Main Switch Override Mechanism
Wake-On-Ring (WOR) header
Wake-On-LAN (WOL) header
Power-on mode control for AC power loss recovery
Internal / External Modem Rign-on
PC Health Monitoring
Voltage
Monitors for CPU Cores +1.8V, +3.3V, +5V, ±12V, +5V Standby
CPU 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
FAN
Total of six 4-pin fan headers
6 fans with tachometer monitoring
Status monitor with firmware speed control
Low noise fan speed control
Status monitor for on/off control
Support 3-pin fans (without speed control)
Pulse Width Modulated (PWM) fan connector
Temperature
Monitoring for CPU and chassis environment
CPU thermal trip support
Thermal Monitor 2 (TM2) support
PECI
LED
CPU / System Overheat LED
Standby Power alert LED
Other Features
Chassis Intrusion Detection
Chassis Intrusion Header
Operating Environment
Environmental Spec.
Operating Temperature: 10°to 35°C (50°to 95°F)
Non-operating Temperature: -40°to 70°C (-40°to 158°F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory
FCC
Passed to meet FCC standard requirement
|