|
Physical Stats
Form Factor
Extended ATX
Dimensions
12.075" x 13.05" (30.7cm x 33.2cm)
Processor/Cache
CPU
Dual 771-pin LGA Sockets
Supports up to two Intel® 64-bit Xeon® processor(s) of the same
type below:
Quad-Core Intel® Xeon®Processor 5400/5300 sequence (Harpertown/Clovertown processor) up to 3.16 GHz
Dual-Core Intel® Xeon®Processor 5200/5100/5000 sequence (Wolfdale/Woodcrest/Dempsey processor) up to 3.40 GHz
System Bus
1333 / 1066 / 667 MHz system bus
Operating System Software
Supports 64-bit Operating Systems
Supports 32-bit Operating Systems
System Memory
Memory Capacity
Eight 240-pin DIMM sockets
Supports up to 32 GB 667 / 533MHz DDR2 ECC FB-DIMM memory
Dual branch memory bus
Memory must be populated in pairs
Memory Mirroring supported
Memory Type
667 / 533MHz FB-DIMM (Fully Buffered DIMM) DDR2 ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
DIMM Sizes
512 MB, 1GB, 2GB, 4GB
Memory Voltage
1.8V only
1.5V(AMB)
Error Detection
Corrects single-bit errors
Detects double-bit errors (using ECC memory)
Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
On-Board Devices
Chipset
Intel® 5000X (GreenCreek) chipset
MCH + PXH-V + ESB2
SAS
Adaptec AIC-9410W Serial-Attached SCSI (SAS) Controller
SAS Dual-Channel (internal)
Each SAS channel supports up to 4 SAS / SATA drives for a total of up to 8 SAS or SATA hard drives
Host RAID 0, 1, & 10 support
SATA
Intel ESB2 SATAII Controller
RAID 0, 1, 5, 10 support (Windows Only)
RAID 0, 1, 10 support (Linux)
RAID
Support for Zero-Channel RAID
RAID 0, 1, 5, 10
Optional: (Card NOT included)
IPMI
Support for Intelligent Platform Management Interface v.2.0
200-pin IPMI slot (SIMLP)
(Optional: AOC-SIMLP-B)
(Optional: AOC-SIMLP-3) with 3rd LAN support
NOTE: KVM-over-LAN not supported - there is no DVO signal to the IPMI slot
Network Controllers
Intel® 82563EB Dual-Port Gigabit Ethernet Controller
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
Intel® I/OAT support for fast, scaleable, and reliable networking
Super I/O
Winbond 83627HG chip
Input / Output
Serial ATA
Six Serial ATA ports
Six SATA hard drives supported
IDE
Single EIDE channel supports up to two UDMA IDE devices(IDE-M, IDE-S) including CF card
Supports UDMA Mode 5, PIO Mode 4, and ATA/100
Compact Flash (40-pin connector, IDE 1, single channel) slot
Floppy
1 Floppy controller; 1.44 MB, 2.88 MB
LAN
2x RJ45 LAN ports
USB
4x USB rear ports
2x USB internal header
6 total USB ports, 2.0 Compliant / 1.1 Compliant
Audio
7.1 High Definition audio
Keyboard / Mouse
PS/2 keyboard and mouse ports
Serial Port / Header
1 Fast UART 16550 serial port
1 Fast UART 16550 serial header
Parallel Port
1 ECP / EEP parallel port
|
|
Chassis ( Optimized for X7DA3+ )
2U Chassis
CSE-825TQ-R700LPV
CSE-825TQ-560LPV
CSE-823T-550LP
3U Chassis
CSE-836E1-R800
CSE-836E2-R800
CSE-833T-550 (SIMLC Support only)
CSE-833T-R760 (SIMLC Support only)
CSE-933E1-R760
CSE-933E2-R760
CSE-933T-R760
CSE-933TQ-R760
Tower / 4U Rackmount
CSE-743T-645
Important Chassis Notes
To ensure system stability, a 500W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required]
Expansion Slots
PCI-Express
1 (x16) PCI-e slot
1 (x4) PCI-e (using x16) slot
PCI-X
2x 64-bit 133/100MHz PCI-X (3.3V) slots
1x 64-bit 100MHz PCI-X (3.3V) slot
PCI
1x 32-bit 33MHz PCI (5V) slot
System BIOS
BIOS Type
8Mb Flash EEPROM with Phoenix® BIOS
BIOS Features
Plug and Play (PnP)
SMBIOS 2.3
DMI 2.3
PCI 2.2
ACPI 1.0
PCI-X 1.0
USB Keyboard support
Hardware BIOS Virus protection
Management
Software
Optional IPMI (Intelligent Platform Management Interface) v2.0
SuperDoctor® III
Watch Dog
NMI
Power Configurations
ACPI Power Management
Main Switch Override Mechansim
Wake-On-Ring (WOR) header
Wake-On-LAN (WOL) header
Keyboard Wakeup from Soft-Off
CPU Fan Auto-off in Sleep Mode
Power-on mode for AC power recovery
Internal/External modem remote ring-on
Suspend to RAM (STR)
PC Health Monitoring
Voltage
Monitors for CPU Cores, +1.8V, +3.3V, +5V, -12V & +5V Standby, VBAT
CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
FAN
Total of eight 4-pin fans
8x fans with status monitoring
Status monitor for speed control
Status monitor for on/off control
Support for 3-pins (w/o speed control)
Low noise fan speed control
Pulse Width Modulated (PWM) fan connectors
Temperature
Monitoring for CPU and chassis, environment
CPU thermal trip support
Thermal Control for 8x Fan Connectors
PSU I2C temperature sensing logic
Thermal Monitor 2 (TM2) support
PECI
LED
CPU / System Overheat LED
Suspend-state Indicator LED
+5V Standby Alert LED
Other Features
Chassis intrusion detection
Chassis intrusion header
SDDC Support
Operating Environment
Environmental Spec.
Operating Temperature: 10°to 35°C (50°to 95°F)
Non-operating Temperature: -40°to 70°C (-40°to 158°F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory
FCC
Class B
|
