Physical Stats
Form Factor
Enhanced Extended ATX
Dimensions
12" x 13.05" (30.5cm x 33.2cm)
Processor/Cache
CPU
Dual 771-pin LGA Sockets
Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
Quad-Core Intel® Xeon®Processor 5400/5300 sequence (Harpertown/Clovertown processor)
up to 3.16 GHz
Dual-Core Intel® Xeon®Processor 5200/5100/5000 sequence (Wolfdale/Woodcrest/Dempsey processor)
up to 3.40 GHz
System Bus
1333 / 1066 / 667 MHz system bus
Operating System Software
Supports 64-bit Operating Systems
Supports 32-bit Operating Systems
System Memory
Memory Capacity
Eight 240-pin DIMM sockets
Supports up to 32 GB 667 / 533MHz DDR2 ECC FB-DIMM memory
Dual branch memory bus
Memory must be populated in pairs
Memory Mirroring supported
Memory Type
667 / 533MHz FB-DIMM (Fully Buffered DIMM) ECC DDR2 SDRAM 72-bit, 240-pin gold-plated DIMMs
DIMM Sizes
512 MB, 1GB, 2GB, 4GB
Memory Voltage
1.8V only
1.5v (AMB)
Error Detection
Corrects single-bit errors
Detects double-bit errors (using ECC memory)
Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
On-Board Devices
Chipset
Intel® 5000X (GreenCreek) chipset
MCH + PXH-V + ESB2
SATA
ESB2 SATAII Controller
RAID 0, 1, 5, 10 support (Windows Only)
RAID 0, 1, 10 support (Linux)
IPMI
Support for Intelligent Platform Management Interface v.2.0
200-pin IPMI slot (SIMLP)
(Optional: AOC-SIMLP-B)
(Optional: AOC-SIMLP-3) with 3rd LAN support
NOTE: KVM-over-LAN not supported - there is no DVO signal to the IPMI slot
Network Controllers
Intel® (ESB2/Gilgal) 82563EB Dual-Port Gigabit Ethernet Controller
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
Intel® I/OAT support for fast, scaleable, and reliable networking
Super I/O
Winbond 83627HF chip
Clock Generator
CK410B chip
Input / Output
Serial ATA
Six Serial ATA ports
Six SATA hard drives supported
IDE
Single EIDE channel supports up to two UDMA IDE devices(IDE-M, IDE-S) including CF card
Supports UDMA Mode 5, PIO Mode 4, and ATA/100
Compact Flash (40-pin connector, IDE 1, single channel) slot
Floppy
1 Floppy controller; 1.44 MB, 2.88 MB
LAN
2x RJ45 LAN ports
USB
4x USB rear ports
1x USB internal header
6 total USB ports, 2.0 Compliant / 1.1 Compliant
Audio
AC97 Audio
Keyboard / Mouse
PS/2 keyboard and mouse ports
Serial Port / Header
1 Fast UART 16550 serial port
1 Fast UART 16550 serial header
Parallel Port
1 ECP / EEP parallel port
|
Chassis ( Optimized for X7DAE )
2U Chassis
CSE-825TQ-R700LPV
CSE-825TQ-560LPV
CSE-823T-550LP
CSE-823i-550LP
Tower / 4U Rackmount
CSE-743T-645 (FAN-0091 Required)
CSE-743i-645 (FAN-0091 Required)
Important Chassis Notes
To ensure system stability, a 500W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required]
Expansion Slots
PCI-Express
1 (x16) PCI-e slot
1 (x4) PCI-et (using x16) slot
PCI-X
2x 64-bit 133/100MHz PCI-X (3.3V) slots
1x 64-bit 100MHz PCI-X (3.3V) slot
PCI
1x 32-bit 33MHz PCI (5V) slot
System BIOS
BIOS Type
8Mb Flash EEPROM with Phoenix® BIOS
BIOS Features
Plug and Play (PnP)
SMBIOS 2.3
DMI 2.1
PCI 2.2
ACPI 1.0
PCI-X 1.0
USB Keyboard support
Hardware BIOS Virus protection
Management
Software
Optional IPMI (Intelligent Platform Management Interface) v2.0
SuperDoctor® III
Watch Dog
NMI
Power Configurations
ACPI Power Management
Wake-On-Ring (WOR) header
Wake-On-LAN (WOL) header
Power-on mode for AC power recovery
Internal/External modem remote ring-on
PC Health Monitoring
Voltage
Monitors for CPU Cores, +1.8V, +3.3V, +5V, -12V & +5V Standby, VBAT
CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
FAN
Total of eight 4-pin fans
8x fans with status monitoring
Status monitor for speed control
Support 3-pin fans
Low noise fan speed control
Temperature
Monitoring for CPU and chassis, environment
CPU thermal trip support
PSU I2C temperature sensing logic
Thermal Monitor 2 (TM2) support
LED
CPU / System Overheat LED
Other Features
Chassis intrusion detection
Chassis intrusion header
Operating Environment
Environmental Spec.
Operating Temperature: 10°to 35°C (50°to 95°F)
Non-operating Temperature: -40°to 70°C (-40°to 158°F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory
FCC
Class B
|