Form Factor
Proprietary
Dimensions
16.24" Length x 11.23" Width (41.25cm x 28.52cm)
Processor/Cache
CPU
Dual 771-pin LGA Sockets
Supports up to two Intel® 64-bit Xeon® processor(s) of the same
type below:
Quad-Core Intel® Xeon®Processor 5400/5300 sequence (Harpertown/Clovertown processor) up to 3.16 GHz
Dual-Core Intel® Xeon®Processor 5200/5100/5000 sequence (Wolfdale/Woodcrest/Dempsey processor) up to 3.40 GHz
System Bus
1333 / 1066 / 667 MHz system bus
Operating System Software
Supports 64-bit Operating Systems
Supports 32-bit Operating Systems
System Memory
Memory Capacity
Eight 240-pin DIMM sockets
Supports up to 32 GB 667/533MHz FB-DIMM memory
Dual branch memory bus
Memory must be populated in pairs
Memory Type
667/533MHz FB-DIMM (Fully Buffered DIMM) ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
DIMM Sizes
512 MB, 1GB, 2GB, 4GB
Memory Voltage
1.8V only
1.5V(AMB)
Error Detection
Corrects single-bit errors
Detects double-bit errors (using ECC memory)
Supports Intel® x4 Single Device Data Correction (SDDC)
On-Board Devices
Chipset
Intel® 5000P (Blackford) chipset
MCH + PXH + ESB2
SATA
ESB2 SATA Controller
RAID 0, 1, 5, 10 support (Windows Only)
RAID 0, 1, 10 support (Linux)
SCSI
Adaptec AIC-7902 Controller
Dual-Channel Ultra320 SCSI (Host RAID only supports 4 drives)
Host RAID 0, 1, 10 support
RAID
Support for Zero-Channel RAID
RAID 0, 1, 5, 10
Optional: (Card NOT included)
IPMI
Support for Intelligent Platform Management Interface v.2.0
200-pin IPMI slot (SIMLP)
(Optional: AOC-SIM1U-3B(+) and AOC-SIM1U-3D)
Network Controllers
Intel® (ESB2/Gilgal) 82563EB Dual-Port Gigabit Ethernet Controller
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
Intel® I/OAT support for fast, scaleable, and reliable networking
Graphics
ATI ES1000 controller with 16 MB of video memory
Super I/O
Winbond 83627HF chip
Clock Generator
CK410B chip
Input / Output
Serial ATA
Six Serial ATA ports
Six SATA hard drives supported
IDE
Single EIDE channel support up to two UDMA IDE devices
Supports UDMA Mode 5, PIO Mode 4, and ATA/100
Floppy
1 Floppy controller; 1.44 MB
LAN
2x RJ45 LAN port
USB
2x USB rear ports
2x USB internal headers, 1 dual, 1 single
USB 2.0 Compliant / 1.1 Compliant
VGA
1x VGA Port
Keyboard / Mouse
PS/2 keyboard and mouse ports
Serial Port / Header
2 Fast UART 16550 serial ports
|
|
Chassis ( Optimized for X7DBP-8 )
1U Chassis
CSE-816S-R700
CSE-816S-700
Important Chassis Notes
To ensure system stability, a 500W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required]
Expansion Slots
Left Universal Slot
1 (x8) PCI-e slot OR
1x 64-bit 100MHz PCI-X (3.3V) slot
Right Universal Slot
1 (x8) PCI-e slot OR
1x 64-bit 133MHz PCI-X (3.3V) slot
IPMI
1 SIM1U Slot (IPMI 2.0)
(Supermicro Intelligent Management)
System BIOS
BIOS Type
8Mb Flash EEPROM with Phoenix® BIOS
BIOS Features
Plug and Play (PnP)
SMBIOS 2.3
APM 1.2
DMI 2.3
PCI 2.2
ACPI 1.0
ACPI 1.0 (limited)
USB Keyboard support
Hardware BIOS Virus protection
Management
Software
Optional IPMI (Intelligent Platform Management Interface) 2.0 / 1.5 - with Virtual Media 8
Optional KVM over LAN & 3rd LAN Port
SuperDoctor® III
Watch Dog
NMI
Power Configurations
ACPI Power Management
Main Switch Override Mechanism
Wake-On-Ring (WOR) header
Wake-On-LAN (WOL) header
Power-on mode for AC power recovery
Internal/External modem remote ring-on
PC Health Monitoring
Voltage
Monitors for CPU Cores, +3.3V, +5V, ±12V, +5V Standby, VBAT
CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.86V-1.63V
FAN
Total of ten proprietary fan headers for up to ten fans
Ten fans with tachometer status monitoring
Status monitor for speed control
Status monitor for on/off control
Low noise fan speed control
Temperature
Monitoring for CPU and chassis environment
CPU thermal trip support
Thermal Control for 8x fan connectors
I2C temperature sensing logic
Thermal Monitor 2 (TM2) support
LED
CPU / System Overheat LED
Other Features
Chassis intrusion detection
Chassis intrusion header
SDDC Support
Operating Environment
Environmental Spec.
Operating Temperature: 10°to 35°C (50°to 95°F)
Non-operating Temperature: -40°to 70°C (-40°to 158°F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory
FCC
Passed to meet FCC standard requirement
|