Physical Stats
Form Factor µATX
Dimensions 9.6" x 9.6 ", (24.4cm x 24.4 cm)
Processor/Cache
CPU
Single LGA775 ZIF Socket
Supports an Intel® Pentium® D (Smithfield Dual Core) processor
Supports an Intel® Pentium® Extreme Edition processor
Supports an Intel® Pentium® 4 processor up to 3.8GHz
Supports an Intel® Pentium® 4 Extreme Edition processor up to 3.73GHz
Supports an Intel® Celeron® D processor with 256KB L2 Cache up to 3.06GHz
Hyper-Threading (HT) capable
2MB / 1MB L2 Cache
Will not support E2000 processors
System Bus
1066 / 800 / 533 MHz system bus
System Memory
Memory Capacity
Four 240-pin DIMM sockets
Supports up to 8 GB of unbuffered ECC / non-ECC DDR2 667/533MHz memory (Dual Channel)
Memory Type
DDR2 667/533MHz unbuffered ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs
DIMM Sizes
256 MB, 512 MB, 1 GB, 2GB
Memory Voltage
1.8V only
On-Board Devices
Chipset
Intel E7230 (Mukilteo) Smithfield chipset
ICH7R + Intel® 82573V/L
Serial ATA
Intel® ICH7R SATA2 (3 Gbps) controller built-in
Intel:
RAID 0, 1, 5, 10 support (Windows Only)
IPMI
1U support for Intelligent Platform Management Interface v.2.0 (Optional: AOC-1UIPMI-B )
Network Controllers
1x Intel® 82573V Gigabit PCI-Express Ethernet
1x Intel® 82573L Gigabit PCI-Express Ethernet
Supports 10Base-T, 100Base-TX, 1000BASE-TX, RJ45 output
VGA
On-board XGI XG20 graphics, 16MB DDR video memory
Super I/O
Winbond 83627H chip
Clock Generator
CK410
Input / Output
Serial ATA
Four Serial ATA ports (3 Gbps performance)
Four SATA hard drives supported
IDE
One EIDE channel supports up to two UDMA IDE devices
Floppy
1 Floppy controller; 1.44 MB
LAN
2 x RJ45 LAN port
USB
6x USB 2.0 compliant / 1.1 compatible
4x internal USB headers
2x rear ports
VGA
1x VGA Port
Keyboard / Mouse
PS/2 keyboard and mouse ports
Serial Ports
1x Fast UART 16550 serial port
1x Header
|
Chassis ( Optimized for PDSML-LN2 )
1U
SC811T-300 (Do not use riser card bracket with IPMI card)
SC513F-260 (OEM and SuperServer only)
SC512F-260 (OEM and SuperServer only)
SC813MFT-300 (OEM and SuperServer only)
CSE-510-200B
4U / Tower
SC743i-645
SC743i-650
SC743i-R760
SC742i-450
SC742i-600
Important Note
To ensure system stability, a 300W (minimum) ATX power supply
[4-pin +12V AND (20 or 24-pin)] is recommended.
Expansion Slots
Universal Slot
1 (x8) PCI-Express Slot OR 1x 32-bit 33MHz PCI Slot
PCI-Express
1 (x4) PCI-e (using x8) slot
PCI
1x 32-bit 33MHz PCI (5V) slot
IPMI
1UIPMI x1
System BIOS
BIOS Type
8Mb Flash EEPROM with Phoenix BIOS®
BIOS Features
Plug and Play (PnP)
DMI 2.3 support
PCI 2.2
ACPI 1.0
ACPI 1.0 (limited)
USB Keyboard support
SMBIOS 2.3
Management
Software
Optional IPMI (Intelligent Platform Management Interface) 2.0
SuperDoctor® III
Watch Dog
Power Configurations
ACPI/APM Power Management
Main Switch Override Mechanism
Wake-On-Ring (WOR) header
Wake-On-LAN (WOL) header
Power-on mode control for AC power loss recovery
PC Health Monitoring
Voltage
Monitors for CPU Cores +1.8V, +3.3V, +5V, ±12V, +5V Standby
CPU 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
FAN
Total of six 4-pin fan headers
6 fans with tachometer monitoring
Status monitor with firmware speed control
Low noise fan speed control
Status monitor for on/off control
Support 3-pin fans (without speed control)
Pulse Width Modulated (PWM) fan connector
Temperature
Monitoring for CPU and chassis environment
CPU thermal trip support
Thermal Monitor 2 (TM2) support
PECI
LED
CPU / System Overheat LED
+3.3V Standby Power alert LED
Other Features
Chassis Intrusion Detection
Chassis Intrusion Header
Operating Environment
Environmental Spec.
Operating Temperature: 10°to 35°C (50°to 95°F)
Non-operating Temperature: -40°to 70°C (-40°to 158°F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory
FCC
Passed to meet FCC standard requirement
|