Physical Stats
Form Factor
Proprietary
Dimensions
16.24" x 11.24" (41.2cm x 28.5cm)
Processor/Cache
CPU
Dual 771-pin LGA Sockets
Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
Quad-Core Intel® Xeon®Processor 5400/5300 sequence (Harpertow /Clovertown processor) up to 3.16 GHz
Dual-Core Intel® Xeon®Processor 5200/5100/5000 sequence (Wolfdale/Woodcrest/Dempsey processor) up to 3.40 GHz
System Bus
1333 / 1066 / 667 MHz system bus
Operating System Software
Supports 64-bit Operating Systems
Supports 32-bit Operating Systems
System Memory
Memory Capacity
Eight 240-pin DIMM sockets
Supports up to 32 GB 667 / 533MHz DDR2 ECC FB-DIMM memory
Dual branch memory bus
Memory must be populated in pairs
Memory Mirroring supported
Memory Type
667 / 533MHz FB-DIMM (Fully Buffered DIMM) ECC DDR2 SDRAM 72-bit, 240-pin gold-plated DIMMs
DIMM Sizes
512 MB, 1GB, 2GB, 4GB
Memory Voltage
1.8V only
1.5V(AMB)
Error Detection
Corrects single-bit errors
Detects double-bit errors (using ECC memory)
Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
On-Board Devices
Chipset
Intel® 5000P (Blackford) chipset
MCH + PXH + ESB2
SATA
Intel ESB2 SATA 3.0Gbps Controller
RAID 0, 1, 5, 10 support (Windows Only)
RAID 0, 1, 10 support (Linux)
IPMI
Support for Intelligent Platform Management Interface v.2.0
200-pin IPMI socket (SIM1U)
(Optional: AOC-SIM1U-3B(+) and AOC-SIM1U-3D)
Network Controllers
Intel® (ESB2/Gilgal) 82563EB Dual-Port Gigabit Ethernet Controller
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
Intel® I/OAT support for fast, scaleable, and reliable networking
Graphics
ATI ES1000 controller with 16 MB of video memory
Super I/O
Winbond 83627HG chip
Input / Output
Serial ATA
Six Serial ATA ports
3 Gbps transfer rate
Six SATA hard drives supported
IDE
Single EIDE channel supports up to two UDMA IDE devices (IDE-M, IDE-S) including CF(Compact Flash) Card
Compact Flash (40-pin connector, IDE 1, single channel) slot
Supports UDMA Mode 5, PIO Mode 4, and ATA/100
Floppy
1 Floppy controller; 1.44 MB, 2.88 MB
LAN
2x RJ45 LAN ports
USB
2x USB rear ports
3x USB internal headers
Total 5 USB 2.0 Compliant / 1.1 Compliant
VGA
1x VGA Port
Keyboard / Mouse
PS/2 keyboard and mouse ports
Serial Port / Header
1 Fast UART 16550 serial port
1 Fast UART 16550 serial header
|
|
Chassis ( Optimized for X7DBX-i )
Important Chassis Notes
To ensure system stability, a 700W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required]
Expansion Slots
Left Universal Slot
1 PCI-Express (x8) Slot OR
1 64-bit 133MHz PCI-X (3.3V) Slot
Right Universal Slot
1 PCI-Express (x4) Slot OR
1x 64-bit 100MHz PCI-X (3.3V) Slot
System BIOS
BIOS Type
8Mb Flash EEPROM with Phoenix® BIOS
BIOS Features
Plug and Play (PnP)
SMBIOS 2.3
DMI 2.1
PCI 2.2
ACPI 1.0
USB Keyboard support
Hardware BIOS Virus protection
Management
Software
Optional IPMI (Intelligent Platform Management Interface) 2.0
SuperDoctor® III
Watch Dog
NMI
Power Configurations
ACPI Power Management
Main Switch Override Mechanism
Wake-On-Ring (WOR) header
Wake-On-LAN (WOL) header
Power-on mode for AC power recovery
Internal / External modem remote ring-on
PC Health Monitoring
Voltage
Monitors for CPU Cores, +3.3V, +5V, ±12V, +5V Standby
5-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
FAN
Total of eight 3-pin fan headers supporting up to 8 fans
8x fans with tachometer status monitoring
Status monitor for speed control
Status monitor for on/off control
Low noise fan speed control
Temperature
Monitoring for CPU and chassis environment
CPU thermal trip support
Thermal Control for 8x fan connectors
PSU I2C temperature sensing logic
Thermal Monitor 2 (TM2) support
LED
CPU / System Overheat LED
Other Features
Chassis intrusion detection
Chassis intrusion header
SDDC Support
Operating Environment
Environmental Spec.
Operating Temperature: 10°to 35°C (50°to 95°F)
Non-operating Temperature: -40°to 70°C (-40°to 158°F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory
FCC
Passed to meet FCC standard requirement
|