|
Form Factor
Proprietary
Dimensions
16.4" x 6.5 " (41.66cm x 16.51cm)
Processor/Cache
CPU
Dual 771-pin LGA Sockets
Supports up to Dual Intel® 64-bit Xeon®processor(s) of the same type below:
Quad-Core Intel® Xeon®Processor 5400/5300 sequence (Harpertown/Clovertown processor) up to 3.16 GHz
Dual-Core Intel® Xeon®Processor 5200/5100 sequence (Wolfdale/Woodcrest processor) up to 3.40 GHz
System Bus
1333 / 1066 MHz system bus
Operating System Software
Supports 64-bit Operating Systems
Supports 32-bit Operating Systems
System Memory
Memory Capacity
Six 240-pin DIMM sockets
Supports up to 48 GB 667/533MHz DDR2 ECC Register DIMM memory
Dual channels memory bus
Memory Type
677/533MHzECC Register DDR2 SDRAM 72-bit, 240-pin gold-plated DIMMs
DIMM Sizes
1GB, 2GB, 4GB, 8GB**
Memory Voltage
1.8V only
Error Detection
Corrects single-bit errors
Detects double-bit errors (using ECC memory)
Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
On-Board Devices
Chipset
Intel® 5100 (San Clemente) chipset
Intel® ICH9R SB
SAS
Brodcom SAS1064E
RAID 0, 1, 10 support
(Optionnal: AOC-IButton68) RAID 5 support
IPMI
Support for Intelligent Platform Management Interface v.2.0
IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
Winbond® WPCM450 BMC
Network Controllers
Intel® 82575 Dual-Port Gigabit Ethernet Controller
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
Intel® I/OAT support for fast, scaleable, and reliable networking
Graphics
Matrox G200 8MB DDR2
Super I/O
Winbond W83627DHG chip
Clock Generator
ICS9LPR501 chip
Input / Output
SAS
4 SAS/ SATA ports
LAN
2x RJ45 LAN ports
1x RJ45 Dedicated IPMI LAN port
USB
2 rear + 1 Type A connector + 2 headers (2 Ports)
5 total USB ports, 2.0 Compliant / 1.1 Compliant
VGA
1x VGA Port
Serial Port / Header
1 Fast UART 16550 serial port
|
|
Chassis ( Optimized for X7DCT-3F)
1U Chassis
CSE-808T-980
CSE-809T-780
Expansion Slots
PCI-Express
1 (x8) PCI-e (using x16 slot)
System BIOS
BIOS Type
16Mb SPI Flash with Phoenix ® BIOS
BIOS Features
Plug and Play (PnP)
DMI 2.3
PCI 2.2
ACPI 1.0/2.0/3.0
USB Keyboard support
Hardware BIOS Virus protection
Management
Software
IPMI (Intelligent Platform Management Interface) v1.5/2.0 with KVM support
SuperDoctor® III
Watch Dog
NMI
Power Configurations
ACPI Power Management
Main Switch Override Mechansim
Power-on mode for AC power recovery
PC Health Monitoring
Voltage
Monitors for CPU Cores,+1.5V, +3.3V, +5V, ±12V, +5 Stdby, VBAT
CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
FAN
Total of three 4-pin fans
3x fans with tachometer monitoring
Status monitor for speed control
Status monitor for on/off control
Low noise fan speed control
Temperature
Monitoring for CPU and chassis environment
CPU thermal trip support
Thermal Control for 3x Fan Connectors
PSU I2C temperature sensing logic
Thermal Monitor 2 (TM2) support
PECI
LED
CPU / System Overheat LED
Suspend-state Indicator LED
Other Features
SDDC Support
Operating Environment
Environmental Spec.
Operating Temperature: 10° to 35° C (50° to 95°F)
Non-operating Temperature: -40° to 70° C (-40° to 158° F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
